Yeah, big 600-plus horsepower numbers are mighty impressive on magazine covers, and those monster lumpy cams will wow all the pretenders at the burger stand on Friday night. But those are wild, wish-book engines that few of us can afford. So let's talk about a street small-block that just about anybody can squeeze out of his wallet.
Powerhouse is a company out of Bakersfield, California, that has been offering stoker engine kits for over 19 years. The 383ci small-block Chevy is its most prolific offering and therefore also the most affordable. Amazingly, you can pick up a stroker small-block Chevy rotator kit from Powerhouse for as little as $580. That's the basic kit, but it does get you a crank, rods, pistons, rings, and bearings, plus a few more pieces. That sounded almost too good to be true, so we decided to build one for ourselves.
Parts And PiecesThe Powerhouse rotating assembly consists of a brand-new Scat crank, rebuilt production 5.7-inch connecting rods, and a set of dished hypereutectic pistons, rings, bearings, and a gasket set. For a few more bucks you can also add balancing, a new, externally balanced Pioneer dampner, and a Pioneer flexplate. Because this is a stroker package, CC's engine master Ed Taylor took a die-grinder to the block's pan rails to ensure the rods would clear. Powerhouse also trimmed the rod bolts to ensure that the rods would clear the camshaft. Finally, Jim Grubbs Motorsports, in Valencia, California, did an excellent job of torque-plate honing to fit the pistons and installing our cam bearings.
Since this is a street engine with a budget focus, we also opted for a set of stock iron Vortec heads. While these heads may sound boring, don't be fooled. Vortecs offer excellent flow for their small 1.94/1.50-inch valve size and, combined with an excellent 64cc combustion chamber, can make outstanding power. All we did was exchange the stock valvesprings for a set of Pioneer conical type springs and elongate the pushrod holes to accommodate the additional lift from the Pioneer 1.6:1 stamped rockers.
To top off our small-block exercise, we chose an Edelbrock Performer Vortec RPM Air Gap intake since we've yet to find a manifold that will beat it when it comes to making both torque and horsepower. See, we're greedy-we want it all. For a carburetor, we stepped up to a Quick Fuel Technologies 750 vacuum secondary carburetor with an electric choke that would ensure good power while still delivering the kind of throttle response and street manners that we've come to expect.
Taylor took his time assembling the Powerhouse 383, ensuring that we had no problems with either the rods and cam or between the rods and the block. Taylor also measured all bearing clearances, crank endplay, and rod side clearances during this trial assembly period to ensure that all the clearances were within spec. This paid off because he did have to make some minor adjustments to bearing clearances, and one pair of rods measured too tight for side clearance, but these are typical issues that were easily remedied.
Test DayOnce Taylor had the Powerhouse 383 fully assembled and pressure-lubed, it went up on the Digilog dyno at Kenny Duttweiler's shop along with a set of 151/48-inch Hooker headers muffled with a pair of 211/42-inch pipes leading to a set of Flowmaster street mufflers. After completing the break-in period for the cam and rechecking the valve lash to ensure nothing changed, we were ready to test.
After the engine was content on 91-octane pump gas with 34 degrees of total ignition timing, the real fun started. Taylor pulled the handle on the dyno and watched as our Powerhouse budget Mouse lived up to its name with 444 lb-ft of torque at 3,600 rpm and a peak power rating of 375 hp at a very conservative 5,400 rpm. As you can see from the Power Curve chart, the engine averaged 404 lb-ft of torque throughout the entire rpm band from 2,200 to 5,800 rpm while delivering a respectable 1,800-rpm power band between peak torque and peak horsepower.