Ad Radar
Car Craft
Click here to find out more!

1999 Chevy Camaro - Study Haul, Part II

Lincoln Tech's 12-Second '99 LS1 Camaro

By J.T. Metz, Photography by Paul Glock

Often in the quest for knowledge, the journey to your destination is more important than your arrival. Lincoln Tech's "bolt-on" Z did deliver on its low-12 second potential, but the events that led up to meeting this goal were much more enlightening than the final results. We're going to tell the whole story, potholes and all.

To recap, Lincoln Technical Institute's Columbia, Maryland, automotive campus "inherited" a 100,000-plus-mile '99 Z28 Camaro. It weighs 3,435 pounds without a driver, including a full complement of working accessories, like leather power seats, A/C, and a kickin' stereo. At the conclusion of Part I, the student techs had equipped it with a set of Hooker long-tube headers, a Flowmaster American thunder exhaust, Alston Frame connectors and control arms, Nitto Drag Radials, a Quartermile Performance Air Box, Rush air filter, 4.10 Richmond gears, an Auburn Pro Posi, and Moser Axles. The Camaro used these bolt-on pieces to great success when it posted a best of 12.85 at 110.03 mph with a 1.94 60-foot time. The Camaro was still traction-challenged, so the students installed an Alston adjustable torque arm with 2 degrees of pinion angle. The Alston bar has a preferred solid mounting to the transmission tunnel rather than the standard rubber isolated transmission mount.

At this point of the project, scientific method gave way to the stark reality of bad weather. Limited available track time made it necessary to bolt on the balance of the available equipment as quickly as possible. The techs now simultaneously installed their SLP-supplied Z06 intake, mass air flow (MAF) sensor, and a BBK 80mm throttle-body and returned to Capitol Raceway in Crotton, Maryland. These modifications made nary a difference as the Camaro pulled down a best of 12.79 at 110.34. The 60-foot times did improve to 1.88, but the new induction package had made no appreciable increase in power.

Undaunted, the students knew that making hp was about proper combinations. They realized that Z06 Corvette camshaft timing had at least 0.030-inch greater gross lift and filed that away for a future fix.

Now the real flogging began. TCI supplied one of its proven 10-inch Street Fighter torque converters. The general consensus was that this would allow the engine to flash to a higher rpm, thereby taking advantage of the intake's true potential. Full of anticipation, the students again drove to Capitol Raceway. Upon its arrival, the Camaro illuminated a check engine light.

An interesting development in modern automotive technology is the various "open loop" or "limp home" modes of operation. The Electronic Control Module will let a car appear to run flawlessly, but not to the point where it can be damaged. The Camaro felt as strong as ever, but one lap showed it was not up to par, running 12.84 at 107.85 with a 1.88 60-foot time. A return to the campus and a meeting with the OBD II scanners showed numerous high-speed misfires. This was accompanied by the embarrassing revelation that the original spark plugs had never been replaced (they looked OK when we put the headers in). A new set of Autolite Platinum Plugs went in, and at this point a decision was made to replace the 4.10 gear with a Richmond 3.73 gear. Conversations with various manufacturers led the students to believe the stock E.C.M. programming might have logic conflicts with the deeper rear gear. The students used a Hypertech reprogrammer for fuel shut off, gear ratio, and tire-diameter adjustments. The Hypertech unit would not improve the fuel and timing settings on the now-non-stock '99 Z. Frankly, with the 4L6OE's 3.06 First gear, a 4.10 probably wasn't necessary.

By J.T. Metz
Enjoyed this Post? Subscribe to our RSS Feed, or use your favorite social media to recommend us to friends and colleagues!
0 comments
Car Craft